RockJock 4x4

For 1997-2006 Jeep TJ's and Unlimited's. The Currie Antirock® sway bar kit provides balanced performance of front and rear suspension for rugged off-road conditions. It gives the driver increased...

Forged Johnny Joint® rod ends feature forged steel construction, a 1 1/4"-12 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.365" wide ball center with...

Currie's heavy duty motor mounts fit all years of Jeep YJ, TJ, LJ, XJ, and MJ vehicles with the 4.0L 6 cylinder engine. These specially designed motor mounts directly replace the stock OEM part...

For 1987-1995 Jeep YJ's These shackles increase rear spring travel by allowing the back eye of the spring to articulate around behind the back end of the frame rail. They feature 1/4" thick steel...

Forged Johnny Joint® rod ends feature forged steel construction, a 1 1/4"-12 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.440" wide ball center with...

Currie 1" lifted motor mounts fit 1987-2006 Jeep TJ/LJ/YJ vehicles equipped with the 4.0L 6 cylinder engine.These specially designed motor mounts lift the front of the engine one inch which produces...

For 1987-1995 Jeep YJ's These shackles increase rear spring travel by allowing the back eye of the spring to articulate around behind the back end of the frame rail. They feature 1/4" thick steel...

Forged Johnny Joint® rod ends feature forged steel construction, a 1 1/4"-12 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.625" wide ball center with...

For 1997-2006 Jeep TJ's and LJ's. Replaces bar pins on after-market front shock installations to properly mount shock absorbers. Bar pin eliminators keep the shock bushings from sliding on the pin...

For 1997-2006 Jeep TJ's and LJ's. Replaces bar pins on after-market rear shock installations to properly mount shock absorbers. Bar pin eliminators keep the shock bushings from sliding on the pin...

Forged narrow body Johnny Joint® rod ends feature forged steel construction, a 1"-14 left hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.625" wide ball...

For 1987-1995 Jeep YJ's - equipped with Pro Comp springs. Replaces stock shackles with our heavy duty units that feature 1/4" thick steel side plates, Energy Suspension "Tough 88" fluted urethane...

Forged narrow body Johnny Joint® rod ends feature forged steel construction, a 1"-14 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.625" wide ball...

This is the specially machined Johnny Joint® rod end out of our CE-9102K front end housing kit. This joint's outer shell is machined to 1.795" o.d. with a flanged edge and is designed to be driven...

For 1997-2006 Jeep TJ's and LJ's. Designed to allow use of the stock sway bar when your vehicle is lifted 3 1/2" to 4 1/2". These extended links directly replace the stock Jeep's sway bar's vertical...

For 1987-1995 Jeep YJ Wranglers - equipped with Pro Comp springs. Replaces stock shackles with our heavy duty units that feature 1/4" thick steel side plates, Energy Suspension "Tough 88" fluted...

For '97-'06 TJ/LJ. Here is a quick way to disconnect your sway bar for maximum articulation for radical rock crawling. Snap-lock clips attach the sway bar link to the mounting pins and allow it to be...

This is the specially machined Johnny Joint® rod end out of our CE-9102K front end housing kit. This joint's outer shell is machined to 1.795" o.d. with a flanged edge and is designed to be driven...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 40" torsion bar length and 18" long steel arms...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 left hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.625" wide ball center with a ...

These are our 4" rear coil springs that are included in our JK 2 or 4-door Johnny Joint® suspension systems. In heavily loaded or and/or hard top 2 or 4 door applications, these springs may not...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 40" torsion bar length and 17" long steel arms...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 left hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.585" wide ball center with a ...

For 1987-1995 Jeep YJ's - equipped with Pro Comp springs. Replaces stock shackles with our heavy duty units that feature 1/4" thick steel side plates, Energy Suspension "Tough 88" fluted urethane...

These are the adjustable length Johnny Joint® rear upper control arms out of the RockJock® JK off road suspension system. Arms are fabricated from 1.25" o.d. x .188" wall d.o.m. steel tubing, feature...

These are our optional 4" rear coil springs that are available for use in our JK 2 or 4-door Johnny Joint® suspension systems. These springs are 1" taller than our standard springs and are most...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 50" torsion bar length and 21" long steel arms as...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 left hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.365" wide ball center with a ...

For 1987-1995 Jeep YJ Wranglers. Replaces stock shackles with our heavy duty units that feature 1/4" thick steel side plates, Energy Suspension "Tough 88" fluted urethane bushings, and heavy duty...

These are our 4" front coil springs that are included in our Johnny Joint® TJ, LJ and JK 4-door suspension systems. These springs may also be used in JK 2-door applications where an extra 1" of...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 50" torsion bar length and 21" long steel arms as...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 left hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.440" wide ball center with a ...

For 1976-1986 Jeep CJ's. Replaces stock shackles with our heavy duty units that feature 1/4" thick steel side plates, Energy Suspension "Tough 88" fluted urethane bushings, and heavy duty greasable...

Coil spring retaining kit for the rear of the JK includes everything to clamp the top of the coil spring to the frame and the bottom of the spring to the axle housing. Sold as a set for both sides -...

These are our optional 4" rear coil springs that are available for use in our Johnny Joint® TJ/LJ suspension system. These springs are 1/2" taller than our standard spring and is most commonly used...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 left hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.625" wide ball center with a...

For 1976-1986 Jeep CJ's. Replaces stock shackles with our heavy duty units that feature 1/4" thick steel side plates, Energy Suspension "Tough 88" fluted urethane bushings, and heavy duty greasable...

These are the adjustable length Johnny Joint® front lower control arms out of the RockJock® JK off road suspension system. Arms are fabricated from 1.625" o.d. x .250" wall d.o.m. steel tubing,...

20" billet aluminum Antirock® sway bar arms as used in our universal Antirock® sway bar kits are available separately for builders or as replacement parts. Arms are machined from 3/4" thick...

These are our optional 4" rear coil springs that are available for use in our Johnny Joint® TJ/LJ suspension system. These springs are 1/2" taller than our standard spring and is most commonly used...

For fabricators and suspension system builders. Currie's Johnny Joints® offer 30 degrees of unrestricted movement in any direction as compared to 22 degrees on a common heim joint. The bushings in...

This is the D.O.T. approved stainless braided extended brake line kit from the RockJock® JK off road suspension system. This kit is ONLY used in conjunction with a rear Antirock® sway bar kit. If...

These are our 4" rear coil springs that are included in our Johnny Joint® TJ suspension system. In heavily loaded TJ or LJ (Unlimited) applications, these springs may not provide a full 4" of lift...

18" billet aluminum Antirock® sway bar arms as used in our TJ, LJ, XJ & MJ Antirock® sway bar kits are available separately for builders or as replacement parts. Arms are machined from...

These are the adjustable length Johnny Joint® front upper control arms out of the RockJock® JK off road suspension system. Arms are fabricated from 1.25" o.d. x .188" wall d.o.m. steel tubing,...

One piece formed and welded heavy-duty plate provides secure mounting points for tow bar attachment to your Jeep JK Wrangler vehicle. The plate bolts directly to the vehicle frame and replaces the...

18" billet aluminum Antirock® sway bar arms as used in our universal Antirock® sway bar kits are available separately for builders or as replacement parts. Arms are machined from 3/4" thick...

This 3" Johnny Joint® rebuild kit includes 2 urethane bushing halves, 2 side washers and 1 snap ring. NOTE: Bushings are 2.535" in diameter.

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 32" torsion bar length and 20" long aluminum arms...

For 1997-2006 Jeep TJ's and Unlimited's. The only bump stop on the market that incorporates coil spring retainers. The bump stops extend stop impact point for proper contact. They are made with...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 32" torsion bar length and 18" long aluminum arms...

These are the adjustable length Johnny Joint® front lower control arms out of the RockJock® JK off road suspension system. Arms are fabricated from 1.625" o.d. x .250" wall d.o.m. steel tubing,...

New Currie trac bar relocator bracket - unlike other brackets on the market - features angle built into the top of the bracket to account for lifts. This keeps your Johnny Joints or bushings on the...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 32" torsion bar length and 20" long steel arms...

This is the D.O.T. approved stainless braided extended brake line kit from the RockJock® JK off road suspension system. Kit fits the front when a front Antirock® sway bar kit is being installed or...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.375" wide ball center with a...

This 2 1/2" Johnny Joint® rebuild kit includes 2 urethane bushing halves, 2 side washers and 1 snap ring. NOTE: Bushings are 2 3/16" in diameter.

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 32" torsion bar length and 20" long steel arms...

Front brake flex hose relocation bracket kit out of our CE-9807S and CE-9802FE kits. Allows the stock brake hoses to be removed from the vehicle, bolted to these brackets with new, supplied hardware,...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.625" wide ball center with a...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 32" torsion bar length and 18" long steel arms...

The all new and improved Johnny Joint® trac bar for the TJ/XJ/LJ/MJ features an offset Johnny Joint® rod end that puts the bar further forward providing more clearance between the diff and the trac...

This 2 1/2" Johnny Joint® rebuild kit includes 2 urethane bushing halves, 2 side washers and 1 snap ring. NOTE: Bushings are 2 3/16" in diameter.

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.585" wide ball center with a ...

This is our complete set of all 8 Johnny Joint® adjustable length control arms for the '07 & up Jeep JK Wrangler. All arms feature heavy tubular steel construction and Johnny Joint® rod ends on both...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 32" torsion bar length and 17" long steel arms...

For fabricators and suspension system builders. Currie's Johnny Joints® offer 30 degrees of unrestricted movement in any direction as compared to 22 degrees on a common heim joint. The bushings in...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.365" wide ball center with a ...

This is the heavy duty bar pin for use at the top of the JK rear shock. These come pre-installed in the Rancho and Walker Evans shocks that we offer for use with our JK kits. Stamped steel...

The Johnny Joint® adjustable length JK rear trac bar features precise bends for a perfect fit into the JK. This bar can be used on a stock JK, on a JK with our Off Road Suspension System, or anything...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.440" wide ball center with a ...

This is the brake flex hose relocation bracket kit out of our CE-9807S Standard Off Road Suspension System. Allows the stock line to be removed from the vehicle, bolted to these brackets with new,...

Forged Johnny Joint® rod ends feature forged steel construction, a 1"-14 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.625" wide ball center with a...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 45" torsion bar length and 20" long aluminum arms...

For fabricators and suspension system builders. Currie's Johnny Joints® offer 30 degrees of unrestricted movement in any direction as compared to 22 degrees on a common heim joint. The bushings in...

The Johnny Joint® rear trac bar for TJ Wranglers and LJ Unlimiteds includes all of the same features as Currie's trail and race proven Johnny Joint® front trac bar and is the perfect complementing...

This new tool from Currie is designed to make the assembly and disassembly of our popular 2" Johnny Joint® rod ends simple! Tool can be used either in a bench vise, or it can also be used on the...

For fabricators and suspension system builders. Currie's Johnny Joints® offer 30 degrees of unrestricted movement in any direction as compared to 22 degrees on a common heim joint. The bushings in...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 45" torsion bar length and 18" long aluminum arms...

LEFT HAND All new from Currie, forged Johnny Joints®!!! We have taken the Johnny Joint® to the next level by making a male rod end style forging that accepts the Johnny Joint® internals...

For fabricators and suspension system builders. Currie's Johnny Joints® offer 30 degrees of unrestricted movement in any direction as compared to 22 degrees on a common heim joint. The bushings in...

RIGHT HAND All new from Currie, forged Johnny Joints®!!! We have taken the Johnny Joint® to the next level by making a male rod end style forging that accepts the Johnny Joint® internals...

This narrow forged 2" Johnny Joint® rod end features forged steel construction, a 7/8"-14 left hand threaded shank and comes fully assembled with 1.600" wide ball center with a 9/16" thru bolt hole...

This narrow style 2 1/2" Johnny Joint® rebuild kit includes 1 urethane bushing, 2 side washers and 1 snap ring. NOTE: Bushing is 2 3/16" in diameter.

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 45" torsion bar length and 20" long steel arms...

This narrow forged 2" Johnny Joint® rod end features forged steel construction, a 7/8"-14 right hand threaded shank and comes fully assembled with 1.600" wide ball center with a 9/16" thru bolt hole...

All new from Currie, forged Johnny Joints®!!! We have taken the Johnny Joint® to the next level by making a male rod end style forging that accepts the Johnny Joint® internals from our CE-9112 2"...

Currie's weld-on Johnny Joint® rod ends for fabricators and suspension system builders offer 30 degrees of unrestricted movement in any direction as compared to 22 degrees on a common heim joint...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 45" torsion bar length and 20" long steel arms...

All new from Currie, forged Johnny Joints®!!! We have taken the Johnny Joint® to the next level by making a male rod end style forging that accepts the Johnny Joint® internals from our CE-9112 2"...

Currie's weld-on Johnny Joint® rod ends for fabricators and suspension system builders offer 30 degrees of unrestricted movement in any direction as compared to 22 degrees on a common heim joint...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 45" torsion bar length and 18" long steel arms...

This 2" Johnny Joint® rebuild kit includes 2 urethane bushing halves, 2 side washers and 1 snap ring. NOTE: Bushings are 1 5/8" in diameter.

For fabricators and suspension system builders. Currie's Johnny Joints® offer 30 degrees of unrestricted movement in any direction as compared to 22 degrees on a common heim joint. The bushings in...

Currie now offers Antirock® sway bar kits in a universal form for those building their own custom rigs and rock buggys. This universal kit features a 45" torsion bar length and 17" long steel arms...