​​​​​​​​​​
Show Filters

Hanson Offroad

Sort By
  • Constructed of 3/16” cold rolled steel. Formed to protect the sides of the vehicle while providing a strong design for bottom impact. The smooth bottom causes no loss in ground clearance and allows for easy sliding over obstacles. The frenched-in steps provide good footing in all weather conditions. This rugged handcrafted construction is finished in a black semi-gloss powder coat

    Hanson

    Hanson JK 2-Door Rocksliders

    Constructed of 3/16” cold rolled steel. Formed to protect the sides of the vehicle while providing a strong design for bottom impact. The smooth bottom causes no loss in ground clearance and allows for easy sliding over obstacles. The frenched-in steps...

    $649.00
    Choose Options
  • Constructed of 3/16” cold rolled steel. Formed to protect the sides of the vehicle while providing a strong design for bottom impact. The smooth bottom causes no loss in ground clearance and allows for easy sliding over obstacles. The frenched-in steps provide good footing in all weather conditions. This rugged handcrafted construction is finished in a black semi-gloss powder coat

    Hanson

    Hanson JK 4-Door Rocksliders

    Constructed of 3/16” cold rolled steel. Formed to protect the sides of the vehicle while providing a strong design for bottom impact. The smooth bottom causes no loss in ground clearance and allows for easy sliding over obstacles. The frenched-in steps...

    $699.00
    Choose Options
  • This skid plate attaches to the back of bumper mounts and to the front factory crash bar. The skid plate is made of 3/16" aluminum and matches the jeeps front grill. It uses the stock crash bar for its strength and adds a great look to your jeep.

    Hanson

    Hanson JK Aluminum Front Skid Plate

    This skid plate attaches to the back of bumper mounts and to the front factory crash bar. The skid plate is made of 3/16" aluminum and matches the jeeps front grill. It uses the stock crash bar for its strength and adds a great look to your jeep.

    $129.00
    Add to Cart Buy Now
  • The handcrafted construction of this sturdy bumper consists of 3/16” cold rolled steel and frenched-in 2” receiver hitch. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. This bumper wraps around the rear body with a thinner profile than stock bumpers. Integrated hitch does not interfere with ground clearance or departure angles. Powder coated in black semi-gloss finish. Hanson's rear bumper works w/stock size tires, if you are going to run larger than stock we suggest our tire carrier.

    Hanson

    Hanson JK Basic Rear Bumper

    The handcrafted construction of this sturdy bumper consists of 3/16” cold rolled steel and frenched-in 2” receiver hitch. The combination of sturdy construction and multiple angles adds strength and optimizes departure angles. This bumper wraps around...

    $899.00
    Choose Options
  • This full width bumper (67") gives maximum protection to the JK fenders. The classic Hanson design, along with a thinner outer wing than stock bumpers, gives the vehicle a cleaner front profile so it looks less bulky. Provides maximum winch and fender protection. The robust design allows for excellent wheel clearance and maximum front-end and fender protection. It’s handcrafted from 3/16” cold-rolled steel. Multiple angles are used in the construction for optimum approach and departure angles. The 2” dropped winch deck accommodates most winches and allows for better airflow to radiator and a lower center of gravity. The multiple angles and the dropped winch deck combined give the bumper superior strength. The winch bar is constructed of 1 ¾” diameter x .120 wall tubing and is angled forward. The fender bars are constructed of 1 5/8” x .120 wall tubing and are angled back and welded for maximum strength. The unique placement and design of the 1” wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with approach and departure angles. Tab is drilled for a 7/8” pin. Bumper provides accommodation for factory driving or after market lights. The well-known value and quality of a Hanson product is exemplified in this handcrafted bumper. It comes in a black semi-gloss powder coat.NOTE: Fairlead Mount Plate, Fairlead, Winch, Off-Road Lights, Recovery Shackles and straps are NOT included with the bumper.

    Hanson

    Hanson JK Fullsize Fenderbar Front Bumper

    This full width bumper (67") gives maximum protection to the JK fenders. The classic Hanson design, along with a thinner outer wing than stock bumpers, gives the vehicle a cleaner front profile so it looks less bulky. Provides maximum winch and fender...

    $899.00
    Choose Options
  • The width of this midsize bumper extends to about the middle of the fender. This gives the bumper a sporty look with ample protection and approach angles for off road use and allows for maximum wheel clearance and good fender protection. It’s handcrafted from 3/16” cold-rolled steel. Multiple angles are used in the construction for optimum approach and departure angles. The 2” dropped winch deck accommodates most winches and allows for better airflow to radiator and a lower center of gravity. The multiple angles and the dropped winch deck combined give the bumper superior strength. The unique placement and design of the 1” wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with approach and departure angles. Tab is drilled for a 7/8” pin. Bumper provides accommodation for factory driving or after market lights. The well-known value and quality of a Hanson product is exemplified in this handcrafted bumper. It comes in a black semi-gloss powder coat. NOTE: Fairlead Mount Plate, Fairlead, Winch, Off-Road Lights, Recovery Shackles and straps are NOT included with the bumper.

    Hanson

    Hanson JK Medium Basic Front Bumper

    The width of this midsize bumper extends to about the middle of the fender. This gives the bumper a sporty look with ample protection and approach angles for off road use and allows for maximum wheel clearance and good fender protection. It’s handcrafted...

    $669.00
    Choose Options
  • The width of this midsize bumper extends to about the middle of the fender. This gives the bumper a sporty look with ample protection and approach angles for off road use. Provides maximum winch and fender protection. The robust design allows for excellent wheel clearance and maximum front-end and fender protection. It’s handcrafted from 3/16” cold-rolled steel. Multiple angles are used in the construction for optimum approach and departure angles. The 2” dropped winch deck accommodates most winches and allows for better airflow to radiator and a lower center of gravity. The multiple angles and the dropped winch deck combined give the bumper superior strength. The winch bar is constructed of 1 ¾” diameter x .120 wall tubing and is angled forward. The fender bars are constructed of 1 5/8” x .120 wall tubing and are angled back and welded for maximum strength. The unique placement and design of the 1” wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with approach and departure angles. Tab is drilled for a 7/8” pin. Bumper provides accommodation for factory driving or after market lights. The well-known value and quality of a Hanson product is exemplified in this handcrafted bumper. It comes in a black semi-gloss powder coat. NOTE: Fairlead Mount Plate, Fairlead, Winch, Off-Road Lights, Recovery Shackles and straps are NOT included with the bumper.

    Hanson

    Hanson JK Medium Fenderbar Front Bumper

    The width of this midsize bumper extends to about the middle of the fender. This gives the bumper a sporty look with ample protection and approach angles for off road use. Provides maximum winch and fender protection. The robust design allows for...

    $869.00
    Choose Options
  • The width of this midsize bumper extends to about the middle of the fender. This gives the bumper a sporty look with ample protection and approach angles for off road use. Provides additional protection for the winch. The robust design allows for excellent wheel clearance and good fender protection. It’s handcrafted from 3/16” cold-rolled steel. Multiple angles are used in the construction for optimum approach and departure angles. The 2” dropped winch deck accommodates most winches and allows for better airflow to radiator and a lower center of gravity. The multiple angles and the dropped winch deck combined give the bumper superior strength. The winch bar is constructed of 1 ¾” diameter x .120 wall tubing and is angled forward and welded for strength. The unique placement and design of the 1” wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with approach and departure angles. Tab is drilled for a 7/8” pin. Bumper provides accommodation for factory driving or after market lights. The well-known value and quality of a Hanson product is exemplified in this handcrafted bumper. It comes in a black semi-gloss powder coat. NOTE: Fairlead Mount Plate, Fairlead, Winch, Off-Road Lights, Recovery Shackles and straps are NOT included with the bumper.

    Hanson

    Hanson JK Medium Winchguard Front Bumper

    The width of this midsize bumper extends to about the middle of the fender. This gives the bumper a sporty look with ample protection and approach angles for off road use. Provides additional protection for the winch. The robust design allows for...

    $769.00
    Choose Options
  • This skid plate attaches to the back of bumper mounts and to the front factory crash bar. The skid plate is made of 3/16" steel and matches the jeeps front grill. It uses the stock crash bar for its strength and adds a great look to your jeep.

    Hanson

    Hanson JK Steel Front Skid Plate

    This skid plate attaches to the back of bumper mounts and to the front factory crash bar. The skid plate is made of 3/16" steel and matches the jeeps front grill. It uses the stock crash bar for its strength and adds a great look to your jeep.

    $129.00
    Add to Cart Buy Now
  • The shorter width of this bumper provides full tire exposure for maximum approach angles. The stout design allows for maximum wheel clearance and front-end protection. It’s handcrafted from 3/16” cold-rolled steel. Multiple angles are used in the construction for optimum approach and departure angles. The 2” dropped winch deck accommodates most winches and allows for better airflow to radiator and a lower center of gravity. The multiple angles and the dropped winch deck combined give the bumper superior strength. The unique placement and design of the 1” wide clevis tabs gives them unmatched strength allowing them to be pulled from any angle without fear of damage to bumper or tab, and do not interfere with approach and departure angles. Tab is drilled for a 7/8” pin. Bumper provides accommodation for factory driving or after market lights. The well-known value and quality of a Hanson product is exemplified in this handcrafted bumper. It comes in a black semi-gloss powder coat. NOTE: Fairlead Mount Plate, Fairlead, Winch, Off-Road Lights, Recovery Shackles and straps are NOT included with the bumper.

    Hanson

    Hanson JK Stubby Basic Front Bumper

    The shorter width of this bumper provides full tire exposure for maximum approach angles. The stout design allows for maximum wheel clearance and front-end protection. It’s handcrafted from 3/16” cold-rolled steel. Multiple angles are used in the...

    $869.00
    Choose Options
  • This unique design is a direct replacement for the stock tire carrier. It is designed to accommodate a 35” tire without putting any additional stress on the tailgate. Unit will also clear a 37" tire, however the complete tire carrier bumper is recommended. Constructed of 1 ½” square .120 wall tubing and a 3/16” gauge steel center. The steel center bolts to the tailgate using factory holes and a gusset bolts to the factory hinges. This design relieves the stress from the tailgate and spreads the load out to the hinges, allowing the unit to carry a larger tire. Black semi-gloss powder coat finish. This unit will work with our rear basic bumper or the stock bumper.

    Hanson

    Hanson JK Tailgate Mount Tire Carrier

    This unique design is a direct replacement for the stock tire carrier. It is designed to accommodate a 35” tire without putting any additional stress on the tailgate. Unit will also clear a 37" tire, however the complete tire carrier bumper is...

    $499.00
    Choose Options